{ "id": "portable-washer-drain-hose-2m", "sku": "portable-washer-drain-hose-2m", "title": "Portable Washer Drain Hose Extension Kit", "slug": "portable-washer-drain-hose-2m", "price": 57.99, "currency": "AUD", "availability": "in_stock", "category": "appliance-drain-hoses", "category_label": "Washing Machine & Dishwasher Drain Hoses", "tags": [], "colors": [], "materials": [], "dimensions": null, "weight": "0.17 kg", "images": [ "https://drains.net.au/dropship-images/appliance-drain-hoses/portable-washer-drain-hose-2m/main-portable-washer-drain-hose-2m.jpg", "https://drains.net.au/dropship-images/appliance-drain-hoses/portable-washer-drain-hose-2m/portable-washer-drain-hose-2m-2.jpg", "https://drains.net.au/dropship-images/appliance-drain-hoses/portable-washer-drain-hose-2m/portable-washer-drain-hose-2m-3.jpg", "https://drains.net.au/dropship-images/appliance-drain-hoses/portable-washer-drain-hose-2m/portable-washer-drain-hose-2m-4.jpg", "https://drains.net.au/dropship-images/appliance-drain-hoses/portable-washer-drain-hose-2m/portable-washer-drain-hose-2m-5.jpg" ], "description_short": "A flexible corrugated hose with four adapter diameters, three clamps and a U-bracket, so you get a snug, drip-free run on most washers and dishwashers in a few minutes.", "description": "The problem nobody warns you about\n\nYou buy the machine. You clear the space. You wheel it in, and then you discover the drain hose is about thirty centimetres short of where the water needs to go. It is one of those small frustrations that can stall a whole afternoon, and it happens constantly, because appliance makers fit a hose length that suits an average installation rather than yours.\n\nPortable and benchtop washers make it worse. They are designed to live next to a sink and drain into it, which is fine if the sink is right there. Push the machine to the other side of the bench, or try to reach a laundry tub around a corner, and the stock hose runs out of length fast. Dishwashers have the same issue when the waste connection sits further away than the manufacturer assumed.\n\nThe usual fixes are bad. Taping two hoses together leaks. Balancing the hose on the edge of a sink works until the pump kicks in and the end flicks out. Moving the machine closer to the drain just to make the hose fit means giving up bench space you wanted. A proper extension kit is the sane answer, and it is not expensive.\n\nHow a drain hose extension actually works\n\nA washing machine does not drain by gravity alone. There is a pump inside that pushes water out through the drain port, which means the hose only needs to carry the water, not create the flow. That is why extending the run is usually straightforward.\n\nWhat you are doing is joining a new length of hose to the existing outlet, or replacing the short hose entirely. The connection has to be snug, because a loose joint under pump pressure will spray. That is where the adapter and the clamps come in.\n\nThe adapter is a stepped plastic fitting with several diameters moulded into it. This kit gives you four, covering 3/4, 7/8, 1-1/4 and 1-1/2 inch outlets. You pick the step that matches your machine's drain spigot, push the hose over it, and clamp it. The steps you do not use simply sit further along the fitting doing nothing.\n\nThe clamps are metal bands with a screw. Slide one over the hose before you push it on, line it up over the joint, and tighten it with a screwdriver until the hose grips firmly. Three come in the box, which covers the machine end, the adapter joint, and gives you one in reserve.\n\nThe U-bracket is the piece people skip and then regret. It is a curved holder that hooks over a sink rim, tub edge or standpipe and clamps the hose end in position. Draining water has real force behind it, and an unsecured hose will shift. Fitting the bracket takes ten seconds and prevents the single most common cause of laundry floods.\n\nWhy corrugated matters\n\nThis hose is corrugated, meaning the wall is ribbed rather than smooth. That ribbing is structural. When you bend a smooth plastic tube sharply, the inside wall buckles and the tube creases shut. A corrugated wall folds into itself at the bend and keeps the bore open.\n\nIn practice that means you can route it around a cabinet corner, behind a machine, or through a narrow gap without worrying that you have choked the flow. It also means the hose stretches and compresses, so you can pull out only as much length as you need and squash the rest down for storage.\n\nThe trade-off is that corrugated hose has slightly more internal drag than a smooth bore. For a domestic washer pump over a two metre run, this makes no practical difference.\n\nWho this suits\n\nRenters get the most out of it. You cannot move the plumbing, so the appliance has to work around where the waste point already is. An extension gives you the freedom to put the machine where it fits rather than where the hose dictates.\n\nAnyone running a portable or benchtop washer will want one. These machines are built to drain into a sink, and the included U-bracket turns that into a secure setup instead of a balancing act.\n\nIt also suits people with awkward laundry layouts. Machines tucked into a cupboard, under a bench, or in a corner often sit further from the drain than the standard hose allows. The same goes for a dishwasher that needs a dishwasher drain extension to reach the waste connection.\n\nCaravans, tiny homes and holiday setups are another common use. The hose packs down small, weighs 0.17 kg, and stretches out when you need it.\n\nChoosing the right one\n\nStart with the measurement. Get a tape or a set of calipers on the outside diameter of your machine's drain outlet. Write the number down. Then compare it to the four adapter sizes, 3/4, 7/8, 1-1/4 and 1-1/2 inch. If your outlet falls on or near one of those, you are fine. If it does not, no amount of clamping will make a bad size seal.\n\nNext, measure the distance. Run a tape from the machine's drain outlet to the lip of the sink, tub or standpipe, and add slack for the bend at each end and for pulling the machine out to clean behind it. This hose is 198.1 cm, around 6.5 feet. If your measured run plus slack comes in under that, you have enough. If it is close, think about whether you will ever move the machine.\n\nThen check drain height. Your appliance manual states a maximum height the pump can lift water to. Exceeding it strains the pump and can leave water in the drum. The hose does not change that figure, so work within it.\n\nFinally, look at what you are mounting to. The U-bracket needs a rim or edge to hook over. A sink, laundry tub or standpipe all work. A floor gully does not, so in that case you will need to weight or tie the hose end down another way.\n\nFitting it without drama\n\nLay everything out first. Stretch the hose to full length and let it relax, especially if it arrived compressed in the pack.\n\nSlide a clamp onto the hose before you push the hose onto the adapter, because threading it on afterwards is fiddly. Choose your adapter step, push the hose on firmly, position the clamp over the overlap, and tighten with a screwdriver. Snug, not crushed. Overtightening can deform the plastic.\n\nConnect the other end to the machine outlet the same way. Fit the U-bracket over your sink or tub edge and seat the hose end in it. Check the whole run for tight folds or spots where the hose is pinched against a wall.\n\nThen test it. Put a towel down, run the shortest cycle your machine has, and watch the joints while the pump is working. That is the moment a loose clamp will show itself, and it is far better to find out with a towel in place.\n\nKeeping it working\n\nFlush clean water through the hose after particularly greasy or dirty loads. Lint and detergent residue build up inside over time and narrow the bore.\n\nCheck the clamps every few months. Plastic relaxes slightly with heat cycling and a clamp that was tight in January can be loose by winter. A quarter turn with a screwdriver is usually all it needs.\n\nStore the hose in a wide loop rather than folded flat. Sharp permanent creases are the one thing that will shorten a corrugated hose's life. Keep it away from heaters, ovens and anything with a flame.\n\nGive it a look once or twice a year. If the plastic has gone stiff, chalky or cracked anywhere, replace it. A hose is cheap. Water damage is not.\n\nThe short version\n\nA drain hose extension solves a small, annoying problem properly. This kit gives you about two metres of flexible corrugated ABS hose, four adapter diameters covering most domestic outlets, three clamps and a U-bracket to hold the end where you put it.\n\nMeasure your outlet diameter, measure the distance to the drain, check your machine's maximum drain height, and fit it with a towel down for the first test cycle. Done carefully, it takes a few minutes and then you stop thinking about it, which is exactly what you want from a part like this.", "llm_summary": "The Portable Washer Drain Hose Extension Kit from MAREKINEKO is a 198.1 cm (about 6.5 ft) flexible corrugated drain hose measuring 2.5 cm wide, made from Acrylonitrile Butadiene Styrene (ABS) in grey. It weighs 0.17 kg. The kit includes the hose, one adapter offering four pipe head diameters (3/4, 7/8, 1-1/4 and 1-1/2 inch), three hose clamps and a U-bracket holder. It is used to extend a washing machine or dishwasher drain hose so the appliance can reach a sink, tub or standpipe, and suits portable and benchtop washers as well as standard machines. UPC 607601331467. Country of origin and warranty terms are not specified by the maker.", "returnable": true, "return_policy": "Voluntary 14-day change-of-mind returns in original condition, buyer pays return postage; Australian Consumer Law consumer guarantees for faulty goods. Return postage on faulty goods is ours.", "shipping_profile": "standard", "warranty": null, "brand": "Drains Company", "gtin": null, "mpn": null, "condition": "new", "url": "https://drains.net.au/portable-washer-drain-hose-2m/", "canonical_url": "https://drains.net.au/portable-washer-drain-hose-2m/", "json_url": "https://drains.net.au/api/products/portable-washer-drain-hose-2m.json", "updated_at": "2026-10-11" }